- 您现在的位置：买卖IC网 > Sheet目录402 > D6F-P0010A2 (Omron Electronics Inc-EMC Div)SENSOR AIRFLOW 0-50KPA W/CONN
D6F-P
Safety Precautions
WARNING
The D6F is built for use with general-purpose devices. In cases
such as those described below, where safety is required, imple-
ment measures to ensure the safety of the system and all
devices, such as fail-safe designs, redundancy designs, and reg-
ular maintenance.
? Safety devices for ensuring safety for persons
? Transportation equipment control (such as applications to stop
operation)
? Aviation and space equipment
? Nuclear power equipment
Do not use the D6F for applications in which D6F operation
would directly affect human life.
Caution
Make sure that the power to all equipment is turned OFF before
you install the Sensor. Installing the Sensor while the power sup-
ply is ON may result in electrical shock or abnormal operation.
Precautions for Correct Use
● Fluids,Tubes, and Sensor Installation
All Models
(1) Use clean fluids. Dust and mist can affect the characteristics
of the Sensor or damage the Sensor. Install a filter and mist
separator on the upstream tube.
(Not required for the D6F-W @ A1 or D6F-P.)
(2) Do not use combustible gases (e.g., hydrogen), corrosive
gases (e.g., chlorine, sulfur, acidic, or alkali gas), or other
non-approved fluids. They may damage the Sensor.
(3) The performance specifications that are given for the G6F
do not apply if any fluids other than the specified applicable
fluid are used.
(4) Foreign matter in the tubes that are connected to the Sensor
may damage the Sensor. Prevent any foreign matter from
entering the tubes after the Sensor is removed from its
packaging.
(5) Attach the tubes so that fluid flows only in the direction des-
ignated by the arrows on the Sensor. Correct measurements
cannot be obtained if the fluid flows in the wrong direction.
(6) We recommend that you install the tubes horizontally. If the
tubes are not installed horizontally, an error of ± 1% FS or
higher may result.
(This does not apply to the D6F-03A3.)
(7) Install the Sensor on a flat surface. Incorrect installation may
damage the Sensor and make it impossible to obtain correct
measurements.
(8) After the Sensor is installed, check to confirm that it oper-
ates correctly.
(9) Do not drop the Sensor, remove the cover, or attempt to dis-
assemble the Sensor in any way.
D6F-P0001A1, D6F-P0010A1, and D6F-P0010A2
(1) Depending on the ambient environment and installation
location, dust, dirt, and other foreign matter may come in
inside the Sensor and block a part or all of the flow path or
accumulate on internal components. This may result in the
Sensor not being able to perform to the specifications given
above. Always perform a pre-evaluation on your actual
equipment and be aware of the possible problems that may
occur before you use the Sensor with the actual equipment.
4
MEMS Flow Sensor
(2) Attach all tubes so that the fluid flows only in the direction
from the positive side ( + ) to the negative side ( ? ).
(3) For PCB-mounting, perform terminal soldering only after the
Sensor is secured into place on the PCB.
(4) Use M2.6 panhead screws or equivalent tapping screws to
mount the Sensor, and tighten the screws to a maximum
torque of 0.59 N·m.
D6F-P0010AM2
(1) Depending on the ambient environment and installation
location, dust, dirt, and other foreign matter may come in
inside the Sensor and block a part or all of the flow path or
accumulate on internal components. This may result in the
Sensor not being able to perform to the specifications given
above. Always perform a pre-evaluation on your actual
equipment and be aware of the possible problems that may
occur before you use the Sensor with the actual equipment.
(2) Attach all tubes so that the fluid flows only in the direction
from the positive side ( + ) to the negative side ( ? ).
(3) Use M3 panhead screws or equivalent tapping screws to
mount the Sensor, and tighten the screws to a maximum
torque of 0.59 N·m.
(4) Install O-rings to seal the fluid inlet and outlet points. The
recommended O-ring is JIS B 2401, nominal number P4.
Installation Example
M3 panhead scre w or a tapping scre w
w ith the same diameter
O-ring
● Operating Environment
Do not use the Sensor in the following locations:
? Locations directly subject to heat radiated from heating equip-
ment
? Locations subject to water or oil
? Locations subject to direct sunlight
? Locations subject to intense temperature changes
? Locations subject to icing or condensation
? Locations subject to excessive vibration or shock
● Countermeasures against Noise
Noise may make it impossible to obtain correct measurements.
Consider the following countermeasures.
? Allow as much space as possible between the Sensor and
devices that generates high frequencies (such as high-frequency
welders and high-frequency sewing machines) or surges.
? Attach surge absorbers or noise filters to noise-generating
devices that are near the Sensor (in particular, equipment with
inductance, such as motors, transformers, solenoids, and
magnetic coils).
(It also helps to separate pipes and ducts, and to use shielded
cables.)
● Power Supply
? Do not directly solder power supply leads to the connector ter-
minals. Use only the appropriate connectors.
? Wire with the correct terminal names and polarities. Incorrect
wiring will cause failure of internal components.
? When using a commercially available switching regulator,
ground the FG (frame ground) and G (ground) terminals.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
D6F-V03A1
AIRFLOW SENSOR 0-3 M/SEC 3.3V
D6F-W CABLE
CABLE FOR D6F FLOW SENSOR 8"
D6F-W10A1
SENSOR AIRFLOW MNT 12/24V
D8M-D82
SENSOR PRESS PULS OUT 0-4.9KPA
DAR-ST2134-Y
STAND W/BASE FOR F3S-/F39-MDG
DC0710J5010AHF
COUPLER 10DB 700-1000MHZ 0805
DC0710J5020AHF
COUPLER 20DB 700-1000MHZ 0805
DC08-73LF
COUPLER DIR 0.81-0.96GHZ SOT-6
相关代理商/技术参数
D6FP0010AM2
制造商:Omron Electronic Components LLC 功能描述:SENSOR;FLOW SENSORS MEMS FLOW SENSOR MANIFOLD MOUNT 制造商:Omron Electronic Components LLC 功能描述:MICRO-FLOW SENSOR - Bulk
D6F-P0010AM2
功能描述:流量传感器 MEMS Flow Sensor Manifold Mount
RoHS:否 制造商:Honeywell 传感器类型:Digital Airflow 额定范围: 精度/可靠性: 模拟输出:- 0.3 VDC to 3 VDC 电源电压:3 V to 10 V
D6F-PH
制造商:OMRON 制造商全称:Omron Electronics LLC 功能描述:High Impedance MEMS Mass Flow Technology
D6F-PH Series
功能描述:流量传感器 High Impedance/Differential Pressure MEMS Mass 流量传感器, 0-250Pa Differential Pressure, 0-70mL Flow Range RoHS:否 制造商:Honeywell 传感器类型:Digital Airflow 额定范围: 精度/可靠性: 模拟输出:- 0.3 VDC to 3 VDC 电源电压:3 V to 10 V
D6FPH0025AD1
制造商:Omron Electronic Components LLC 功能描述:SENSOR AIRFLOW 0-250PA PCB TERM
D6F-PH0025AD1
功能描述:流量传感器 MEMS Differential Pressure 0 to 250Pa
RoHS:否 制造商:Honeywell 传感器类型:Digital Airflow 额定范围: 精度/可靠性: 模拟输出:- 0.3 VDC to 3 VDC 电源电压:3 V to 10 V
D6FPH0505AD3
制造商:Omron Electronic Components LLC 功能描述:SENSOR AIRFLOW +/- 50PA PCB TERM
D6F-PH0505AD3
功能描述:流量传感器 Micro Flow DP Sensor -50 to +50Pa
RoHS:否 制造商:Honeywell 传感器类型:Digital Airflow 额定范围: 精度/可靠性: 模拟输出:- 0.3 VDC to 3 VDC 电源电压:3 V to 10 V